SEARCH

Getting Started
1g DSM Datalogging
OBDII Datalogging
Rtek7 ECU Upgrade
PDA Information

PocketLOGGER DSM
PocketLOGGER OBDII
PocketLOGGER ZT
KnockBOX
Rtek7 ECU Upgrade
Jeep Window Block
Hotsync Cables
PL Log Viewer

PocketLOGGER DSM
PocketLOGGER OBDII
KnockBOX
Rtek7 ECU Upgrade
PDA Information
Forum
Ordering/Shipping
Warranty/Returns
Help Ticket
About Us
Contact Us
IMPORTANT
Summer Closure
RX7 ECU's, both DTI install and self install, will NOT be processed between July 8th and July 15th. If your ECU is received after July 5th, it will not be processed until after July 17th. Please plan your ECU shipment to us accordingly. All other non-Rtek orders will be processed normally during this time.

Resetting a Palm

How to reset a Palm handheld

Under normal use, you should not have to use the reset button located on the back of your Palm(tm) handheld. On rare occasions, however, your handheld may not respond to taps on the screen. In this case, you need to perform a reset to get your handheld running again.

The Palm handheld can be reset in three different ways:

A Soft Reset
A Warm Reset
A Hard Reset

Performing a Soft Reset

A Soft reset tells your handheld to stop what it is doing and start over again. All records and entries stored in your handheld are retained with a Soft reset. After a Soft reset, the Palm logo screen appears, followed by the General Preferences screen.

To perform a Soft reset, do the following:

  • Use the tip of an unfolded paper clip (or similar object without a sharp tip) to gently press the reset button inside the hole on the back panel of your handheld.

Performing a Warm Reset

A Warm reset bypasses any system extensions (such as hacks, OS patches, etc.) that are loaded on your handheld. Performing a Warm reset often bypasses the "boot loop" error, and allows you to remove any recently installed third party applications that might be causing the problem.

To perform a Warm reset, do the following:

  • Press and hold the Page Up button on your handheld.
  • Use the tip of an unfolded paper clip (or a similar object without a sharp tip), gently press the reset button inside the hole on the back panel of your handheld.
  • When the Palm logo appears on the screen, release the Page Up button.

Performing a Hard Reset

With a Hard reset, all records and entries stored in your handheld are erased. Formats, preferences and other settings are restored to their factory default settings. You can restore any data previously synchronized with your computer during the next HotSync(r) operation. You should re-install your 3rd party applications unless you are using Palm OS(r) 3.3 (or higher) or a third party backup solution that automatically backs up and restores installed applications. Never perform a Hard reset unless a Soft or Warm reset does not solve your problem.

To perform a Hard reset, do the following:

  • Hold down the power button on the front panel of the handheld.
  • While holding down the power button, use the tip of an unfolded paper clip (or similar object without a sharp tip) to gently press the reset button inside the hole on the back panel of your handheld.
  • Release the reset button.
  • When the Palm logo appears on the screen, release the power button.
  • When the message appears on the screen warning that you are about to erase all the data stored on your handheld, do one of the following: Press the page up button on the front panel of the handheld to complete the Hard reset and display the Digitizer screen or press any other button to perform a Soft reset.

 

Still Lost?:
If you still haven't found what you're looking for, you can take a look at our help section.

Customer review:
PocketLOGGER for DSM:
I love my PocketLOGGER, go Digital Tuning, go!
-Chris D., Matthews, NC
Other Products:
Hotsync Cables
Hotsync Cables
Price: $19.95 - $29.95


Sitemap  |  Press Room  |  Legal Information  |  Privacy Information

2001-2010 digital tuning, inc. All rights reserved.